Spray Foam Removal near me in Bridgwater is the fast, mess-controlled way to strip failed polyurethane foam from lofts, rafters and cavity walls. We handle open cell and closed cell spray foam, cut it out, extract the dust and leave timber ready for a surveyor. If a lender, insurer or surveyor has flagged your insulation, our local spray foam removal Bridgwater team can be on site this week.
Spray Foam Removal near me in Bridgwater means physically cutting, blasting and extracting cured polyurethane foam from the roof timbers, loft floor, rafters and cavity walls of your property, then disposing of it under controlled conditions. It is not a chemical spray-over and it is not a cover-up. Foam is removed back to bare timber, the roof space is cleaned, ventilation is restored and the structure is left ready for a surveyor, lender or insulation reinstatement.
Bridgwater homes get hit by the same problem again and again: foam sprayed between rafters in the 2000s and 2010s, then a mortgage valuation or home insurance renewal flags it. Trapped moisture rots roof timber, blocks loft ventilation and causes condensation and damp. If you need cheap spray foam removal near me Bridgwater without cutting corners, we survey first, quote a fixed price and start work the same week.
Every job is scoped after the free survey, so you know exactly what is covered before we start. Standard removal covers access, containment, extraction, timber inspection and waste disposal. Reinstatement of new insulation, plastering or roof repairs is quoted separately if you need it.
A full inspection using a boroscope inspection camera, moisture meter and thermal imaging camera. We identify the foam type, measure timber moisture content and check eaves ventilation, then give you a fixed written price the same day.
Floor sheeting, doorway seals, an air scrubber and a negative air machine keep dust and fumes out of your living space. Our crew wears PPE disposable coveralls and respirator filters throughout, and we vacuum every surface before handover.
Bulk foam is cut with an oscillating multi-tool, reciprocating saw and hammer drill, then residue is lifted with a dry ice blasting machine, sand blasting equipment or thermal methods. An industrial vacuum extraction unit runs continuously to capture debris.
Every rafter is checked for rot, with moisture readings and photographs logged. We confirm the vapour barrier and breathable membrane are intact and that loft ventilation is clear, then hand you a report suitable for a lender, buyer or insurer.
All foam waste is bagged, removed from site and disposed of responsibly, with paperwork provided. You get before-and-after photographs and a clean, swept loft that is ready for a surveyor to inspect the same day.
We attend your Bridgwater property, usually within 48 hours of your call, and inspect the loft, rafters and cavity. A boroscope inspection camera and moisture meter tell us the foam type, depth and whether timber is already damp. You get a written fixed price the same day, no charge for the survey.
On day one we sheet floors, seal doorways and position an air scrubber and negative air machine so dust and odour stay in the work zone. PPE disposable coveralls and respirator filters go on before any cutting starts. Setup takes 45 to 90 minutes on a typical three-bed semi.
Foam comes out with an oscillating multi-tool, reciprocating saw and hammer drill for the bulk, then dry ice blasting machine or sand blasting equipment for the residue bonded to timber. An industrial vacuum extraction unit runs continuously. A standard loft takes one to two days; a full roof and cavity job runs three to four.
Once the foam is off, we check every rafter with a moisture meter and thermal imaging camera. Any rot is logged with measurements and photographs. We confirm the vapour barrier and breathable membrane are intact and that eaves ventilation is clear before reinstatement work is discussed.
We bag and remove all foam waste, vacuum the space, wipe down timbers and leave the loft swept. You get a removal report, before-and-after photographs and disposal paperwork. Most Bridgwater jobs finish with the loft ready for a surveyor within 24 hours of the last visit.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Lifts closed cell foam residue from timber without water or abrasive grit, which protects older rafters and avoids adding moisture to an already damp roof space.
Used for stubborn foam bonded to brick, dense timber or irregular surfaces where cutting tools cannot reach. Dust is controlled with air scrubbers and negative air machines throughout.
Runs continuously during cutting and blasting to capture foam fragments and dust at source, keeping the rest of your Bridgwater property clean and breathable.
Lets us inspect behind rafters, inside eaves gaps and under foam without opening up the structure, so we can confirm foam type and hidden rot before quoting.
Measure timber moisture content and reveal cold bridging or damp pockets that are invisible to the eye. Readings are logged for your removal report.
The primary cutting tools for bulk foam removal. The multi-tool handles detail work around rafters and services, while the reciprocating saw clears larger panels quickly.
A three-bed semi in Wembdon had closed cell foam sprayed across every rafter, with a buyer's surveyor flagging it and the lender refusing to proceed. Timber moisture readings were creeping up and two rafters showed early staining.
We removed the foam in three days, cleared the eaves gap and logged moisture readings across all rafters. The two stained rafters were treated and monitored rather than replaced, and the removal report went to the lender within 24 hours of handover.
A 1970s semi in Durleigh had open cell foam blocking the eaves, causing condensation and brown damp patches on two bedroom ceilings. The loft smelled musty and ventilation was effectively zero.
Foam was cut out and extracted in a single day, the eaves gap was reopened and airflow restored at both ends of the roof. An air scrubber ran throughout, and the ceilings dried within two weeks once the source was gone.
A landlord in Bridgwater Town Centre had two rental terraces with dense closed cell foam and an insurer threatening to cancel cover at renewal. One loft had visible rot on three rafters near the eaves.
Both lofts were cleared within a week using cutting tools and dry ice blasting, with the three rotten rafters documented and repaired. Waste disposal paperwork and before-and-after photographs were issued, and the insurer reinstated cover.
Most calls we take are triggered by a surveyor, a lender or a damp patch. These are the four problems we fix most often across Bridgwater and the surrounding Somerset villages.
Ask a pro →We survey within 48 hours, remove the foam, document the timber condition and issue a removal report with photographs and moisture readings. Lenders and surveyors get the evidence they need, and most Bridgwater clients see a revised valuation within two to three weeks.
We cut foam back to bare wood, check every rafter with a moisture meter and thermal imaging camera, and log any rot with measurements and photographs. Catching decay at 18 to 22 percent moisture content usually avoids structural repairs entirely.
Removing the foam reopens the eaves gap and restores airflow. We confirm the vapour barrier and breathable membrane are serviceable, check ventilation at both eaves, and run an air scrubber during the work so odour and spores do not spread through the house.
Our removal pack gives insurers proof the foam is gone, the timber is sound and the waste was disposed of properly. Clients in Sydenham and Hamp have had policies reinstated within days of receiving the report, often alongside a mortgage lender spray foam removal case.
Call us on 0127 827 6038 and we will book a free survey, usually within 48 hours. We cover Bridgwater Town Centre, Eastover, Hamp, Wembdon, Durleigh and the surrounding villages. The survey confirms the foam type, roof size and timber condition, and you get a fixed written price the same day. No deposit is needed to book the survey.
We are based in Bridgwater and work across Somerset daily, so we are usually the nearest crew for postcodes in and around the town. Typical attendance is within 48 hours for a survey and the same week for removal. For urgent surveyor or exchange deadlines we can often be on site within 24 hours.
Yes. We cover Bridgwater Town Centre, Eastover, Hamp, Wembdon, Durleigh, Haygrove, Stockmoor Village, Willow Manors, Sydenham, Bower Manor, Chilton Trinity, North Petherton Road, Taunton Road, Bath Road, Puriton, Pawlett, Woolavington, Cannington, Dunball and Combwich. If you are just outside that list, call and we will confirm coverage and travel the same day.
Survey attendance is normally within 48 hours, and removal usually starts the same week. A standard three-bed loft takes one to two days on site, while a full roof and cavity wall job runs three to four days. If a lender or buyer has set a deadline, tell us the date when you call and we will schedule around it.
Same day Spray Foam RemovalWhen a surveyor is due or an exchange date is looming, same day spray foam removal gets a crew to your Bridgwater property fast. We carry cutting, blasting and extraction kit on the van, so a small loft bay can often be cleared and documented in a single visit.Explore →
24/7 Spray Foam RemovalFor commercial premises, landlords and urgent insurance deadlines, our 24/7 spray foam removal line stays open. We schedule out-of-hours work across Bridgwater so removal does not disrupt tenants, staff or trading hours, and we still deliver the same removal report and disposal paperwork.Explore →
Residential Spray Foam RemovalMost of our Bridgwater work is residential: semis, terraces and bungalows with foam sprayed between rafters. We protect carpets and furniture, work room by room, and leave the loft clean enough for a surveyor to inspect the same day. Fixed price agreed after the free survey.Explore →
Commercial Spray Foam RemovalWarehouses, workshops and agricultural buildings around Dunball and Puriton often carry thick closed cell foam. We scale crews and extraction equipment to the square metreage, work around your operating hours, and provide waste transfer documentation for commercial compliance records.Explore →
Loft Spray Foam RemovalLoft spray foam removal is our most common Bridgwater job. Foam between rafters traps moisture, blocks eaves ventilation and rots timber. We cut it back to bare wood, clear the eaves gap, check the vapour barrier and breathable membrane, and hand back a loft that is ready for reinstatement.Explore →
Roof Spray Foam RemovalFoam sprayed directly onto the underside of roof tiles or sarking is harder to reach and needs careful cutting. Our roof spray foam removal team works from inside the roof space, using boroscope inspection cameras to check for hidden rot before we start cutting near the membrane.Explore →
Attic Spray Foam RemovalOlder Bridgwater attics often have foam over the joists as well as the rafters. Attic spray foam removal clears both, restores airflow and lets us inspect the ceiling structure. We bag and remove all waste and vacuum the space before handover.Explore →
Spray Foam Insulation RemovalFull spray foam insulation removal covers open cell, closed cell and mixed foam systems in one visit. We identify the product, often Isothane, BASF or Huntsman, then choose the right cutting and blasting method so timber is not damaged during extraction.Explore →Free survey, fixed written price and a removal report your lender can read. We are CHAS accredited, Constructionline registered and fully insured, and we have been stripping foam across Somerset since 2022. Call today and we will book your survey within 48 hours.
Get free survey 0127 827 6038 →Call 0127 827 6038 or email us and a technician will get back to you the same working day. We answer the phone from 8am to 6pm Monday to Friday, and our emergency line is staffed 24/7 for urgent foam problems. Free surveys across Bridgwater and the surrounding villages, usually booked within two working days.