Roof Spray Foam Removal in Bridgwater is what we do every week across Somerset. If your surveyor has flagged spray foam insulation, your mortgage is on hold, or your loft smells damp, we take the foam out without wrecking the roof timber underneath. We cover Bridgwater Town Centre, Wembdon, Sydenham and the surrounding villages, with same-day assessments and a written report your lender will accept.
Roof Spray Foam Removal in Bridgwater is the controlled extraction of polyurethane foam from the underside of your roof covering and rafters, followed by cleaning, inspection and reinstatement of ventilation. We do not just hack it off. Closed cell spray foam sets like rock, so we cut it back in sections, check every roof timber with a moisture meter, and clear the loft ventilation paths that the foam blocked in the first place.
Most Bridgwater jobs we quote come from one of three situations: a mortgage lender refusing to proceed until the foam is gone, a surveyor flagging spray foam insulation on a Level 2 report, or condensation and damp appearing on rafters after a few winters. Older terraces around Eastover and Hamp are the usual suspects, because they were built with breathable roofs that spray foam simply suffocates. If you have been searching roof insulation removal near me Bridgwater, that is exactly the job we turn up for.
Every quote covers the full job from assessment to completion pack, so there is no stage where you are left chasing a separate trade. What varies is the amount of timber repair and the roof size. Here is what is standard on a Bridgwater job.
We inspect the foam type, coverage and timber condition using a boroscope inspection camera and moisture meter, then give you a fixed written price the same day. You get the findings in writing whether or not you book the work.
Extraction uses an oscillating multi-tool, reciprocating saw and dry ice blasting machine, with an industrial vacuum extraction unit running throughout. Negative air machine and air scrubber keep dust and spray foam odour out of your living space.
Every exposed rafter is probed and moisture-tested. Fungal growth is treated with Envirograf, and decayed sections are cut out and spliced. All findings are photographed and logged for your lender or surveyor.
We clear blocked eaves vents, fit breathable membrane where needed, and reinstate loft insulation correctly. Airflow is confirmed with a thermal imaging camera before we sign the job off.
All foam waste is bagged and removed from site for correct disposal. We do not leave foam debris in your loft, garden or skip for you to deal with afterwards.
You receive photos, moisture readings, treatment records and a workmanship warranty within 48 hours of handover. The pack is written to be forwarded straight to a mortgage lender or surveyor.
We attend, access the loft, and inspect the foam type, coverage and timber condition. A boroscope inspection camera and moisture meter tell us within 30 minutes whether the rafters are sound. You get a fixed written price the same day, usually within two hours of the visit.
We sheet the loft floor, seal doorways, and set up a negative air machine with an air scrubber so no foam dust or odour travels into your living space. PPE disposable coveralls and respirator filters are standard on every job. Setup takes about 45 minutes on a typical semi.
Using an oscillating multi-tool, reciprocating saw and dry ice blasting machine, we cut and lift the foam off the rafters in controlled sections. An industrial vacuum extraction unit runs continuously to capture debris. A standard three-bedroom loft takes one to two days; larger roofs run to three.
With the foam gone, we probe every rafter and treat any fungal growth with Envirograf timber treatment. Rotten sections get cut out and spliced. We photograph everything for your records. This stage usually adds half a day and is what makes the difference at surveyor level.
We clear blocked eaves vents, fit breathable membrane and correct loft insulation, then confirm airflow with a thermal imaging camera. You get a completion pack with photos, moisture readings and a workmanship warranty. Final handover takes about an hour.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Lifts foam off rafters without gouging the timber or leaving chemical residue. Our preferred method on older Bridgwater roofs where the rafters are already marginal.
Runs continuously during extraction to capture foam debris at the source, so it does not end up in your loft insulation or through the rest of the house.
Creates negative pressure in the loft and filters the air, keeping spray foam odour and fine dust out of your living space while we work.
Lets us see behind rafters and into eaves without opening up more of the roof than necessary, so we can confirm timber condition before quoting repair work.
Gives us hard readings on timber moisture and confirms airflow after ventilation is reinstated. These readings go into your completion pack as evidence.
Controlled cutting of closed cell foam in sections, which is the only safe way to remove hard-bonded foam from a roof deck without tearing the lining.
A three-bed semi in Wembdon had closed cell foam sprayed across the entire roof deck by a previous owner. The buyer's lender refused to proceed and the sale stalled with the chain already formed.
We removed the foam over two days, treated two rafters with Envirograf, and reinstated eaves ventilation. Moisture readings dropped from 24% to 15% over the following ten weeks, and the completion pack went to the lender within 48 hours of handover.
A Victorian terrace in Eastover had condensation dripping from the rafters every winter. The owner had already paid for two roof inspections chasing a leak that did not exist.
We identified the foam as the cause, removed it with dry ice blasting in a single day, and cleared the blocked eaves vents. The loft dried back to 13% moisture over the summer and there were no drips the following winter.
A landlord in Hamp had three terraced properties all foamed by the same contractor years earlier. Tenants had reported damp and the properties were becoming hard to let.
We worked through all three over consecutive weeks, removing open cell foam, treating minor fungal growth, and reinstating loft insulation and breathable membrane. All three lofts came back under 16% moisture, and the properties were re-let without damp clauses.
Spray foam causes a predictable set of problems, and most of them get worse the longer the foam stays in place. These are the ones we are called out for most often across Bridgwater and the surrounding villages.
Ask a pro →We remove the foam, document the timber condition with photos and moisture readings, and issue a completion pack your broker can forward. Most Bridgwater clients see their offer reinstated within two to three weeks of the work finishing.
We strip the foam, probe every rafter, and treat fungal growth with Envirograf. Decayed sections are cut out and spliced while the roof is open. Catching it at this stage typically saves a full re-roof later.
Removing the foam and reinstating eaves ventilation restores airflow. We confirm the fix with a thermal imaging camera and moisture meter before handover, and most Bridgwater lofts dry back to 12-16% within two to three months.
We handle the removal to a documented standard, with PAS 2035 principles applied to the reporting. You get evidence of what was removed, what condition the timber was left in, and what was reinstated, which is what lenders and insurers actually ask for.
Typical 2026 pricing in Bridgwater runs from around 1,800 to 4,500 pounds for a standard house, depending on roof size, foam type and how much timber repair is needed. A single loft conversion sits at the lower end; a full terrace roof with closed cell foam and rot treatment sits at the top. You get a fixed written price after the free assessment.
Yes. We remove open cell spray foam and closed cell spray foam from rafters, roof deck and trusses using dry ice blasting and controlled cutting, then clean the timber back to bare wood. Every rafter is probed and moisture-tested afterwards. If we find rot, we treat it with Envirograf or splice the timber while the roof is open.
It usually does, because condensation is caused by the foam sealing the roof deck and trapping moisture against cold timber. Once the foam is out and eaves ventilation is reinstated, airflow returns and readings drop. Most Bridgwater roofs we finish dry back to 12-16% moisture over two to three months. We confirm airflow with a thermal imaging camera before handover.
A standard three-bedroom loft takes one to two days for extraction, plus half a day for timber inspection and treatment. Larger or heavily foamed roofs run to three days. From your first call to a finished completion pack, most Bridgwater jobs are wrapped up inside a week, and lender paperwork is issued within 48 hours of handover.
Spray Foam Removal near meOur core spray foam removal service covers lofts, rafters and roof decks across Bridgwater. If you are searching for spray foam removal near me because a surveyor has flagged it, this is the starting point, and we will tell you on the assessment whether the roof needs full extraction or partial.Explore →
Same day Spray Foam RemovalWhen a mortgage deadline or a leak forces the pace, we can often get to Bridgwater properties the same day for assessment and start work immediately after. Same day spray foam removal is subject to access and foam type, but we will always tell you honestly what is achievable.Explore →
24/7 Spray Foam RemovalWater tracking through a foamed roof at 2am does not wait for office hours. Our 24/7 spray foam removal line covers Bridgwater and the surrounding villages for emergency call-outs, so you can get someone on the phone and a plan in place before the damage spreads.Explore →
Residential Spray Foam RemovalMost of our Bridgwater work is residential spray foam removal on houses, bungalows and terraces. We work around family routines, keep dust contained with negative air machines, and leave the loft clean enough to use the same week we finish.Explore →
Commercial Spray Foam RemovalCommercial spray foam removal covers warehouses, workshops and commercial units around Dunball and Bridgwater's industrial estates. Larger spans mean different access and extraction planning, and we schedule work around your operating hours so the building stays usable.Explore →
Loft Spray Foam RemovalLoft spray foam removal is the most common job we quote in Bridgwater. Foam sprayed directly onto the underside of roof tiles or between rafters traps moisture and blocks ventilation. We remove it, check the timber, and put the loft back to a breathable, usable state.Explore →
Attic Spray Foam RemovalAttic spray foam removal follows the same timber-safe process as our loft work, with extra care around older trusses and heritage roof structures. Properties around Chilton Trinity and Cannington often have irregular attic framing that needs a slower, more careful extraction.Explore →
Spray Foam Insulation RemovalSpray foam insulation removal is about reversing a bad insulation decision without losing the thermal benefit. After extraction we reinstate loft insulation and breathable membrane correctly, so your roof performs the way it should have from the start.Explore →If a lender, surveyor or a damp patch in the loft is pushing you to act, call us on 0127 827 6038. We are CHAS accredited and fully insured, and we will give you a fixed written price after a free assessment. Most Bridgwater jobs are assessed within 48 hours.
Get a free assessment 0127 827 6038 →Call 0127 827 6038 or email us and a technician will get back to you the same working day. We answer the phone from 8am to 6pm Monday to Friday, and our emergency line is staffed 24/7 for urgent foam problems. Free surveys across Bridgwater and the surrounding villages, usually booked within two working days.